Thursday, 24 July 2014 13:37

PTZ Control

 

 

 

 

PELCO D commands

http://info.kmtronic.com/pelco-d-commands.html

 

 

 

 

 

 

 

 

 

 

 

http://www.fritzbox.eu

 

 

 

 

 

NOTE
SOME FRITZ!Box modems require RJ-45 REVERSE POLARITY CAT5 CABLE !
 

RJ45 - Reverse Polarity 

 

1. Connect LAN board to any PC or Laptop and using this procedure enable DHCP:

http://www.info.kmtronic.com/how-to-change-default-settings-kmtronic-lan-board.html

 

 

 

2. Connect board to FRITZ!Box and check IP board (in this example 192.168.178.20):

 

 

 

 

3. Click on IP address and open Relay board WEb Server

 

 

 

--- Tested with FRITZ!Box 7390 ---

 

 

 

 

 

 

 

 

 

 

KEEProg EEPROM programmer

 

 

 

Download Software and Drivers from:

http://info.kmtronic.com/software/KEEPROG/KEEProg_EEPROM/KEEProg_EEPROM_3.4.zip

 

 

 

WINDOWS XP

 

 

UnZip in separate folder ( in example D:\KEEProg )

 

 

Open Device Manager

 

Connect programmer to PC

 

 

Click on KEEProg EEPROM PROGRAMMER and next Update Driver...

 

 

Click on Browse my computer ...

 

 

Locate driver’s holder and click Next

 

Wait until Windows install driver

 

 

 

Windows will show confirmation message that drivers are installed

 

 

 

Close and open again Device Manager to check that KEEProg programmer is now installed

 

 

Run software

 

 

 

 

 

 

WINDOWS 7

 

 

 

 

 

 

 

 

 

 

 

 

 

Tuesday, 18 February 2014 08:18

ModbusView and Modbus TCP Relay board

 

 

 

 

 

ModbusView TCP Software

https://oceancontrols.com.au/OCS-011.html

 

 

 

 

 

 

 

 

 

 

05 (0x05) Write Single Coil LOG

 

web-8relay-modbus-mobile

 

 

 

 

 

 

 

 

Tuesday, 18 February 2014 08:07

MACH3 Modbus TCP

 

 

 

 

Mach3 is PC-based CNC software

http://www.machsupport.com/

 

 

 

 

 

 

 

 

 

 

 

 

Tuesday, 18 February 2014 08:04

Modbus Relays



 LAN Ethernet IP 8 channels Modbus/TCP Relay board

 



KMtronic RS485 Modbus 8 Relays

www.info.kmtronic.com/kmtronic-modbus-relays.html

RS485 ModBus Relays by Loxone Miniserver and ModBus extension Control KMtronic USB, RS485 and TCP(Web) relay boards by Domoticz

www.info.kmtronic.com/rs485-modbus-relays-by-loxone-miniserver-modbus.html



MACH3 and KMtronic Modbus/TCP 8 Relay board

www.info.kmtronic.com/mach3-and-kmtronic-modbus-tcp-8-relay-board.html



ModbusView and KMtronic Modbus/TCP 8 Relay board

www.info.kmtronic.com/modbusview-and-modbus-tcp-relay-board.html


ModbusTools and KMtronic Modbus TCP 8 Relay board Control KMtronic USB, RS485 and TCP(Web) relay boards by Domoticz

www.info.kmtronic.com/modbustools-and-kmtronic-modbus-tcp-relay-board.html

 

 

 


 

 

Modbus RS485 RTU Serial to

Modbus LAN TCP/IP Module Converter

 

KMtronic Modbus LAN TCP/IP to Modbus RTU RS485 Serial Communication Module Converter

 

 

 

www.info.kmtronic.com/modbus-tcp-ip-converter.html

 

 

 

 

 

 

 

 

 

 

 

 

http://www.loxone.com

 

http://www.loxone.com/enuk/service/documentation/extensions/rs485.html

 

 

... On the configuration program just go to Periphery - Devices - RS485 Extension and

just use the following communication parameters: 8 Data, 1 Stop, No Parity, Baud rate : 9600.

Now add a RS485 actuator. Click use as digital output,

write \xFF\x01\x01 on "Command for on" and \xFF\x01\x00 on "Command for off"

and you can control the first relay channel.

Repeat the above for the other relays (\xFF\x02\x01 and \xFF\x02\x00 for the second, so on)....

 

 

Thank you Vampiris!

 

 

 

 

 

 

 

http://www.info.kmtronic.com/Loxone_and_KMTronic_RS485_Relay_Board.pdf

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

http://www.info.kmtronic.com/software/Web_2_Relay/Web_2_Relay_CMD.zip

 

 

 

Commands:


WEB_Relay 1 1

WEB_Relay 1 0

WEB_Relay 0 1

WEB_Relay 0 0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Friday, 14 February 2014 07:48

Arduino Examples

 

 Arduino

 

 

Controlling UART 8 Relay board by Arduino

http://info.kmtronic.com/arduino-uart-8-channel-relay-controller-example.html

 

Controlling KMTronic Relays by Arduino ADK

http://info.kmtronic.com/controlling-kmtronic-relays-by-arduino-adk.html

 

Connecting a relay to Arduino

www.info.kmtronic.com/arduino-two-relay-board.html

 

Arduino network power switch

http://info.kmtronic.com/arduino-network-power-switch.html

 

 

 

 

 

 

 

 

Friday, 14 February 2014 07:39

UART Relay board Examples

 

 

 

KMtronic UART 8 Channel Relay Controller

 

 

 

Controlling UART 8 Relay board by Arduino

https://info.kmtronic.com/arduino-uart-8-channel-relay-controller-example.html

Controlling UART 8 Relay board by RaspberryPi

https://info.kmtronic.com/controlling-uart-8-relay-board-by-raspberry-pi.html

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 7 of 41